Easy Sign, Difficult Customer

At the end of May, my daughter and pickiest customer Mira, turned eight and planned to have a mermaid swimming party at Grandma’s house. Grandma has a swimming pool and we knew that she would be willing to heat it for an early-season swim, so it was an easy choice. The difficult part was finding mermaid themed items that met with Mira’s approval and weren’t for little girls (Ariel, A.K.A. The Little Mermaid, is not cool when you are eight).

While searching for party decorations, my wife, Chris, came across a little sign that she thought was cute and asked if I could make one for the party. It said, “Mermaid Lagoon” and it was pretty simple, and since it was right up my alley, being made of wood and all, I said “Yes”.

I dug out some cypress that had lots of knots and a good rustic look and started cutting. I wanted the sign to be bigger (who wouldn’t) than the one in the photo, so I cut the boards about two feet long to make the height. I trimmed the ends at random lengths, some at a slight angle, until I had enough to make the sign about three feet wide. It went quick, especially since I had no formal plan. If a board didn’t look right, I just trimmed it more or flipped it around or just grabbed another board. I love that kind of woodworking; no tape measure, no pencil, no worries.

After I nailed the boards together, I painted them with a wash of blue/green paint. I already had some bright blue paint in the shop and added green Transtint to get the color right. I thinned the paint down with water and brushed it on as quick as possible. While it was still wet, I wiped it off like it was a stain to show the wood below.

Once the paint was dry, I did the lettering, which I laid out and printed from the computer. I cut out the words with an X-acto knife and used a light coat of Super 77 spray adhesive to hold it in place while I painted it. A light mist of white spray paint did the trick, making the words legible but not too pronounced.

After the sign panel was assembled and painted, I needed to come up with a post. My first attempt was a weathered piece of oak 2″x4″. It had the right look and feel since it was old and gray, but I thought that Mira might not approve since it just looked like an old board, so I continued to search for a better way to display it.

A quick walk to the other end of the shop revealed a piece of driftwood that was perfect. It was the right size and height, and with just a little block added to the bottom, it sat up beautifully crooked. Plus, I wouldn’t have to pound it in the concrete-like ground since it would stand up on its own. That piece of white oak driftwood couldn’t have worked out better.

All that was left to do was screw the sign to the post, which took a grand total of 30 seconds. If it was going to be for long-term use I would have been more serious about it, but two 3″ deck screws worked just fine and quickly put this job to bed.

The perfect piece of white oak driftwood and cypress lumber teamed up to make this sign for my daughter Mira's swimming party.

The perfect piece of white oak driftwood and cypress lumber teamed up to make this sign for my daughter Mira’s swimming party.

I was pleased as punch. I showed it to everyone within shouting distance of the shop and couldn’t wait to bring it home and show the girls. They were pleasantly surprised at how it turned out and I was pleasantly surprised that Mira quickly approved it (I was still a bit worried that my unauthorized driftwood addition might have been a bit aggressive in her mind (even though it was perfect)). We capped the whole thing off with hot glue, a few seashells and then perfect weather for a “Mermaid Lagoon” swimming party.

The sign now resides in my shop, where it generates many inquiries, but as of today, no more official orders for driftwood mermaid signs.

 

Advertisements

Tags: , , , , , , , ,

About wunderwoods

Hi! My name is Scott Wunder and I am the owner of WunderWoods Custom Woodworking. We build wine cellars, built-ins and furniture from local woods, here in St. Louis, MO. Recently, I finished a three-year term as the President of the St. Louis Woodworkers Guild, which had me writing a monthly article for our newsletter. I love to write, especially about wood, and found that I still had more to say. Every day I run into something wood related that I realize some of my customers don't know and this seems like a great forum for sharing what I have learned (instead of telling the same story to each person). The main thing to remember is that I try to keep it light and as my wife always reminds people that have just met me, "He is joking."

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: