Woodworking With Gloves: Am I Crazy?

Before you answer that question, let’s discuss.

This photo was in a recent newsletter from Fine Woodworking. Notice the gloves?

Everything I read regarding safety in the shop says don’t wear gloves when operating machinery. Gloves can get caught in moving parts and suck you in. It makes sense. Don’t wear loose clothing, tie back your hair and don’t wear gloves. But, I am not one to just let things go unquestioned. Are gloves in the shop really that dangerous?

These are the gloves that I currently wear from Home Depot.

I almost always wear gloves in the shop, even while operating machinery. They are tight-fitting cloth gloves with nitrile-dipped palms from Home Depot. I like them because they are inexpensive, fit great, aren’t too hot, and give me excellent grip. I especially like to wear them when I am using the jointer, but I find the grip to be helpful any time that I am pushing smooth-planed wood through a tool like the table saw.

I use the jointer (mine is 12″ wide) to flatten the wide face of all of my lumber before it goes through the thickness planer, leaving it flat and straight. On wider, longer and heavier boards it takes a lot of force to move them across the jointer. Often, I am really leaning into it and the gloves are the only way that I can get enough grip. I know push blocks are recommended, but they are slow and very cumbersome to use when you are faced with several days of jointing rough lumber.

On the table saw and router table, the enemy is smooth wood. I constantly envision myself losing my grip and pushing my hand right into the action. Guards, of course, would help, but we all know that there isn’t one on my table saw and there probably isn’t one on yours either. On the router table it is easier to cover the cutter and be productive, but I still want a good grip, so that I don’t jam my hand into the bit. I think gloves are the answer.

So, why are gloves dangerous? They are dangerous because if you accidentally touch that table saw blade, instead of just getting cut, you will get cut, sucked in, and cut some more. To that, I say, “Well, don’t touch the blade.” I have been doing this a long time and I still get a little nervous when my hand is getting in the vicinity of the blade. I pay attention, think about what could go wrong and try to avoid it. I always picture myself at my college bakery job at 3 a.m. making donuts. I am tired, the floor is covered with grease, my knees are locked and I am leaning forward over a boiling vat of death. But, no matter how tired I was, I knew that if I lost my balance and fell forward, I was going to catch myself on the side of the fryer and not in the bottom of the hot oil. The thought of my hand frying like a donut goes a long way to making me focus and so does the idea of sticking my hand in the table saw. Gloves aren’t an issue if you keep your hands out of the saw.

Now that I have tempted fate and thrown it out to the universe, let’s say my hand does go into the proverbial “fryer”. If I am wearing a glove, is my result guaranteed to be worse because of it? I have heard stories from friends of friends and distant acquaintances on the internet about how things were bad because of a glove. But, what about the times that an accident was averted because of gloves? It is certainly possible. Nobody is going to tell a story of how they didn’t put their hand in the saw because they had a firm grip and everything went smoothly. There is no gore there, no tale of doom to pass down from generation to generation.

I would only use these loose-fitting gloves for moving lumber. Not for work around tools.

With this in mind, I tried to be more scientific and find studies about gloves in the workplace. The one that I found to be the most relevant only asked questions of people who were injured on the job and whether they were wearing gloves or not. They really needed to ask glove wearers about specific times when the gloves either made their outcomes better or worse. But again, worse outcomes are going to get more airtime because you can’t identify when things went better or nothing went wrong.

For now, I am still wearing my gloves. They make me feel confident when I am close to the tools, and I think that goes a long way towards safety. In the meantime, I hope to find more scientific data and plan to do some tests by sticking gloves in the tools to see how things go. I just need to find some volunteers.

Let me know your thoughts and if you have any first-hand accounts.

Advertisements

Tags: , , , , , , ,

About wunderwoods

Hi! My name is Scott Wunder and I am the owner of WunderWoods Custom Woodworking. We build wine cellars, built-ins and furniture from local woods, here in St. Louis, MO. Recently, I finished a three-year term as the President of the St. Louis Woodworkers Guild, which had me writing a monthly article for our newsletter. I love to write, especially about wood, and found that I still had more to say. Every day I run into something wood related that I realize some of my customers don't know and this seems like a great forum for sharing what I have learned (instead of telling the same story to each person). The main thing to remember is that I try to keep it light and as my wife always reminds people that have just met me, "He is joking."

One response to “Woodworking With Gloves: Am I Crazy?”

  1. Jim Motto says :

    This is good stuff. I am sold. I am headed out right now to get some ..donuts.
    thx.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: